PRODUCT DESCRIPTIONS
Alabama outdoor state flags are USA made of nylon flag material and are finished with a canvas heading and two brass grommets on the hoist side, 2 rows of stitching top and bottom sides and 4 rows of stitching on the fly side. They are attached to the flagpole by means of a halyard (rope) and flag snaps, or to smaller poles with flag fasteners. Standard sizes for outdoor state flags are 2x3 ft, 3x5 ft, 4x6 ft, 5x8 ft, and 6x10 ft.

Extra large outdoor nylon Alabama flags are offered in 8x12 ft, 10x15 ft and 12x18 ft. Production process includes a #10 white nylon rope is sewn into the 2” cotton polyester blend header. Galvanized metal thimble ends are crimped to the rope ends for attachment to the flag snaps. An additional brass grommet is placed midway on the heading for use with a third flag snap for durability and stability on the halyard.

Extreme wear outdoor Alabama flags are produced using open weave 2-ply woven polyester, the longest wearing flag material available for daily, long-term display. This open weave material reduces fabric stress and outside fly-end shredding in high wind applications, allowing for up to double the wear of traditional nylon flags. Sizes offered are 3x5 ft, 4x6 ft and 5x8 ft. Textile trade names are Annin Flagmakers Tough-tex or Eder Flag Mfg. Poly-Max.

Alabama boat flags are nylon, 12”x18” size with 2 brass grommets.

Alabama indoor flags are available in 3x5 ft and 4x6 ft. nylon, and feature a pole sleeve with a flannel liner and a tab sewn inside the sleeve. The tab attaches to a hook or screw a top of the parade or display flagpole to keep the flag from sliding down the pole. Indoor and parade flags are finished with two-inch gold rayon fringe. These flags are also available with a pole sleeve only and no fringe (made to order, allow 2 weeks). All indoor flags are USA made.

3x5 ft indoor flags are typically displayed on either 7 ft or 8 ft poles. 4x6 ft indoor flags are typically displayed on 9 ft poles. Poles are available in polished hardwood and either silver or gold anodized aluminum. Indoor floor stands are available in either weighted ABS plastic or cast metal in gilt, brass or chrome finishes. Flagpole finials for indoor / parade poles are available in ABS plastic and both brass or chrome metal finishes.

Alabama desktop flags are made in the United States. Size is 4 x 6 inch, lightweight nylon material, hemmed all four sides, mounted on 10” black staffs with a golden spear point. Table top bases are available in black plastic to display from 1- 7 flags. Wood bases are available with either 10 holes or 12 holes to display additional flags.

Alabama stick flags, hand held mounted flags are 8 x 12 inch, lightweight nylon, fully hemmed, mounted on a ¼” x 18” black wood dowel with a golden spear point, and made in America. Sold in quantities of 12/box only, please call to order.

Alabama classroom flags for school districts are 12”x18” lightweight poly flags hemmed on all four sides and mounted on 3/8” x 30” black wood staff with golden spear tip. Sold in quantities of 12 / box only, please call to order.

FLAG DESCRIPTION / HISTORY
Statehood: 1819, the 22nd state
Year Flag Adopted: 1895
The Alabama State Flag was authorized by the Alabama Legislature on February 16, 1895, by Act number 383. According to the Acts of Alabama, 1895, the state flag was to be a crimson cross of St. Andrew on a field of white. The bars forming the cross were not to be less than six inches broad and were to extend diagonally across the flag from side to side. The act did not designate a square or a rectangular flag. A 1987 opinion by the Office of Attorney General of Alabama established the flag shape as rectangular. (ref. Alabama State Archives) January 2014.